Utilize este identificador para referenciar este registo: https://hdl.handle.net/10216/103414
Registo completo
Campo DCValorIdioma
dc.creatorP. Ribeirinha
dc.creatorM. Boaventura
dc.creatorJosé Carlos B. Lopes
dc.creatorJosé M. Sousa
dc.creatorA. Mendes
dc.date.accessioned2022-09-08T03:51:59Z-
dc.date.available2022-09-08T03:51:59Z-
dc.date.issued2014
dc.identifier.issn0360-3199
dc.identifier.othersigarra:105509
dc.identifier.urihttps://hdl.handle.net/10216/103414-
dc.description.abstractThree reformers with different designs (multi-channel, radial and tubular) were developed for thermal integration with a high temperature polymeric electrolyte membrane fuel cell (HT-PEMFC). They were characterized experimentally at temperatures between 443 K and 473 K, using the commercial catalyst G66 MR from Sud-Chemie (CuO/ZnO/Al2O3). The reactors were modeled and simulated using a computational fluid dynamics (CFD) analysis. The models were validated using experimental data. The results showed that the multi-channel design is the best solution for thermal integration with a HT-PEMFC, presenting high methanol conversion and low pressure drop. Regarding the heat transfer ability, the multi-channel showed also the best performance, presenting the lowest temperature sink among the studied reformers. The low flow velocities and the absence of metallic surfaces in the radial reformer had detrimental effect on the heat transfer. Concerning the flow distribution a coefficient of variation of 0.6% was observed in the multichannel reformer. A quasi plug flow behavior was found in the tubular and a multichannel (channels region only) reformer, while in the radial a not fully developed laminar flow was found. At temperatures lower than 473 K was found that the reformate stream did not require further purification to be fed to a HT-PEMFC due to the low CO concentration (<1600 ppm). The advantages and limitations of each design is discussed based on experimental data and CFD modeling. Copyright
dc.language.isoeng
dc.relationinfo:eu-repo/grantAgreement/COMISSÃO EUROPEIA/7.º Programa-Quadro de IDT/303476/Integrated low temperature methanol steam reforming and high temperature polymer electrolyte membrane fuel cell/BeingEnergy
dc.relationinfo:eu-repo/grantAgreement/FCT - Fundação para a Ciência e a Tecnologia/Projectos de I&DT em Todos os Domínios Científicos/PTDC/EQU-EQU/104217/2008/Integração de células de combustível de electrólito de membrana polimérica com membranas de paládio de elevada eficiência/PTDC/EQU-EQU/104217/2008
dc.rightsrestrictedAccess
dc.subjectEngenharia do ambiente
dc.subjectEnvironmental engineering
dc.titleStudy of different designs of methanol steam reformers: Experiment and modeling
dc.typeArtigo em Revista Científica Internacional
dc.contributor.uportoFaculdade de Engenharia
dc.identifier.doi10.1016/j.ijhydene.2014.10.029
dc.identifier.authenticusP-00A-0FX
dc.subject.fosCiências da engenharia e tecnologias::Engenharia do ambiente
dc.subject.fosEngineering and technology::Environmental engineering
Aparece nas coleções:FEUP - Artigo em Revista Científica Internacional

Ficheiros deste registo:
Ficheiro Descrição TamanhoFormato 
105509.1.pdfPost-Print version2.83 MBAdobe PDFThumbnail
Ver/Abrir
105509.pdf
  Restricted Access
Artigo original publicado1.8 MBAdobe PDFVer/Abrir


Todos os registos no repositório estão protegidos por leis de copyright, com todos os direitos reservados.